Abstract
Nanocrystalline Fe-Si-B-Nb-Cu Finemet alloys show low saturation magnetic flux density compared to amorphous Fe-Si-B alloys. In the Fe-Si-B-Cu base amorphous alloys, Cu atoms form clusters which act as heterogeneous nucleation sites for α-Fe crystals. The addition of Ca element atoms, distributed along grain boundaries, helps inhibit grain growth and increase..... More

Abstract
In this study, oxide (Y₂O₃)-embedded Ni particles were fabricated via a new process. The process involves the mechanical hydrogenation of Ni–Y alloy into Ni–YH₂ and the selective oxidation of Ni–YH₂ to Ni–Y₂O₃. The alloy powders were prepared for sintering by the mechanical alloying of a mixed powder. The powder was..... More

Abstract
The effects of the cooling rate, after solution heat treatment, on the microstructures and mechanical properties of Fe-22Mn-8Al-0.8C-0.02Nb (low carbon) and Fe-20Mn-8Al-1.1C-0.1Nb (high carbon) light-weight steels were systematically investigated. The cooling process was controlled to achieve six different cooling rates, ranging from -0.016 to -465.1 ^oC/s. Under the slowest cooling..... More

Abstract
ZrO₂ is a promising candidate for knee and hip joint replacements due to its excellent combination of low density, corrosion resistance and biocompatibility. Nevertheless, a low fracture toughness of pure ZrO₂ at room temperature limits its wider application in the industry. One of the most obvious ways to solve the..... More

Abstract
Recent large-scale fires in buildings and logistic warehouses have become a major social issue, involving both property loss and multiple casualties. To make color coated steel sheets non-combustible and/or have anti-fire properties, various ways of optimizing manufacturing parameters have been investigated for outer, inner, roof and ceiling panels. In the..... More

Abstract
In this study, consolidated WC-Fe compacts as a function of Fe contents were fabricated by a spark plasma sintering method, following the mixed by the ball-milled powder. Fe among the metallic binders was added to WC enhance not only the driving force of sintering process but also suppressing the grain..... More

Abstract
This study examined the effect of alkalis on lyocell-based activated carbon fibres (ACFs) with high Brunauer-Emmett-Teller (BET) surface areas, using X-ray diffraction (XRD). Here, alkali treatments were conducted using 10 ~ 25 % NaOH and KOH on lyocell samples for 3 h at ambient room temperature. A secondary treatment with..... More

Abstract
Tungsten carbides are quite attractive for their superior properties, e.g., high melting point, high hardness, high thermal and electrical conductivities, and relatively high chemical stability. Tungsten carbides with a binder metal, for example Co or Ni, are mainly used to produce cutting tools, nozzles and molds in the composite form...... More

Abstract
In this study, we report how Cu doping can modify the thermoelectric performance of p-type Bi_0.5Sb_1.5Te3 and Bi_0.4Sb_1.6Te3 thermoelectric alloys, including their electronic and thermal transport properties. For electronic transport, the power factors of both Bi_0.5Sb_1.5Te3 and Bi0.4Sb1.6Te3 compositions were increased by Cu doping. The origins of the enhanced power..... More

Abstract
The powder-alloyed metallic sheet foam manufacturing process has the advantage of being able to control pore shape, size, and distribution more easily and homogeneously than conventional foam manufacturing processes. The effects of strain rate and tensile direction on the mechanical properties of Ni-Cr-Al superalloy foam fabricated by powder alloying method..... More

Abstract
The effects of heat treatment conditions on the mechanical properties and energy absorption capacity of 7003 (Al-6Zn-0.6Mg) aluminum alloy were studied. The extruded material was heat treated at various temperatures to prepare annealed or aged specimens. Tensile tests, hardness measurements, electron backscatter diffraction characterizations, and differential scanning calorimeter analyses were..... More

Abstract
The use of locally developed high performance alloys in power plants has become essential in the past ten years. Application of these alloys has been difficult because of a shortage of field demonstration testing, and the lack of lab-based test data. In this work, three types of locally developed heat..... More

Abstract
Al₂O₃ has a high Young’s modulus (380 GPa), a low density (3.98 g· cm^-3), good high-temperature mechanical properties, biocompatibility and excellent oxidation resistance. Al₂O₃ has been used for automotive, aerospace, bio-materials and various industrial applications. Despite its various merits, the low fracture toughness of the material below the brittle-ductile transition..... More

Abstract
Alloy design of 9Cr-1Mo-V-Nb weld metals was carried out through thermodynamic simulation, and elevated temperature tensile testing was performed on the designed alloy. Based on the thermodynamic simulation of the 9Cr-1Mo-V-Nb weld metal, 0.09 to 0.10 wt% C was added to increase Cr-rich M₂₃C₆. Nitrogen was reduced from 0.04 to..... More

Abstract
The effects of natural and pre-aging on the microstructure and mechanical properties of Al-8.0Zn-2.5Mg-2.0Cu aluminum alloy sheet fabricated by twin roll casting were investigated. Immediately after solution treatment, the Al-8.0Zn-2.5Mg-2.0Cu alloy sheet had a yield strength of 173 MPa and elongation of 19.5%. The hardness of the Al-8.0Zn-2.5Mg-2.0Cu alloy sheet..... More

Abstract
Electrical steel is a soft magnetic steel material used in electric devices such as transformers and motors. The performance of these electric devices is primarily related to the magnetic properties of electrical steel, and the assessment of the magnetic properties of electrical steel has been considered an important topic. We..... More

Abstract
ZnO/Ag/SnO2 (ZAS) tri-layer films were prepared on glass substrates via RF and DC magnetron sputtering, and then the influence of the thickness of the ZnO and SnO2 layers on the optical and electrical properties of the ZAS films was investigated. As deposited ZnO 50 nm/Ag 10 nm/SnO2 50 nm films..... More

Abstract
Aluminum nitride (AlN) has several attractive properties including high thermal conductivity, excellent electrical insulation, a thermal expansion coefficient close to that of Si and low density. Accordingly, it is considered a promising packing material and substrate for high power integrated circuits. However, its low fracture toughness at room temperature limits..... More

Abstract
Aluminum alloys have been widely used for aerospace applications due to their high strength and lightweight. New demand is growing for aluminum alloys with high temperature mechanical properties that can sustain plastic deformation at high temperature. In this study, correlations among microstructure, tensile properties and Charpy impact properties were analyzed..... More

Abstract
In micro/nano electro-mechanical system, silicon nitride (SiNx) membrane has been widely used in sensors, energy harvesting and optical filters because of its mechanical/chemical stability. However, it is necessary to verify mechanical and thermal properties of nanoscale SiNx membranes to ensure the desirable reliability and durability of a device because the..... More

Abstract
This study was carried out to investigate the effect of fatigue stress magnitude on the tensile properties of the damaged Fe – 22Mn – 12Cr – 3Ni – 2Si – 4Co damping alloy under various fatigue stress magnitudes. α´ and ε-martensite were formed by fatigue stress in the Fe –..... More

Abstract
In spite of the many attractive properties of (W,Ti)C, its low fracture toughness limits its wide application. To improve the fracture toughness generally a second phase is added to fabricate a nanostructured composite. In this regard, graphene was considered as the reinforcing agent of (W,Ti)C. (W,Ti)C-graphene composites that were sintered..... More

Abstract
This study investigated the microstructure and room temperature mechanical properties of W-7Ni-3Fe (wt%) tungsten heavy alloy (as-fabricated) which was manufactured by metal injection molding (MIM). To identify the effect of heat treatment on the W-7Ni-3Fe alloy, its properties were compared after heattreatment (1,100 oC for 1 hour) in vacuum atmosphere...... More

Abstract
The microstructure, tensile properties at room and elevated temperatures, and high-cycle fatigue behavior of an extruded Mg-7Sn-1Al-1Zn (TAZ711) alloy were investigated in comparison with those of an Mg-8Al-0.5Zn (AZ80) alloy extruded under the same conditions. The extruded AZ80 alloy exhibited a fully recrystallized structure, whereas the extruded TAZ711 alloy had..... More

Abstract
This study investigated the crystal structure and mechanical properties of copper foil electroplated by adjusting gelatin and chloride ions from 0 to 100 ppm. There was increased formation of spherical crystals and surface roughness on the surface of the electroplated layer when the gelatin was added, and the direction of..... More

Abstract
Electroplated copper has been used as wiring in electronic circuit boards and as cathode materials for secondary batteries, and its usage has expanded into the construction industry because of its convenient production and high economic value. During the electroplating process, various parameters, such as crystal phase and size, can affect..... More

Abstract
This study investigated the effects of manufacturing conditions, such as patenting temperature and drawing strains, on the tensile fracture behaviors, especially on reduction of area (RA), of hyper-eutectoid steel wire. Steel wires with the chemical compositions of Fe-0.92C-1.3Si-0.6Mn-0.3Cr (wt%), were austenitized at 900 °C for 3 min and isothermally transformed..... More

Abstract
This study manufactured Fe-Cr-Ni-based alloy (HK30) using the metal injection molding (MIM) process and investigated the microstructure and room·high temperature mechanical properties of the material. The effect of hot isostatic pressing (HIP) on properties was also examined. The average grain sizes were 24.1 µm for an MIM specimen and 29.1..... More

Abstract
An inorganic binder is a good way to mitigate the environmental issues of organic binders containing phenol, formaldehyde, etc. One of the most representative materials in the field of inorganic moulding sand binders is a group of binder systems based on alkali silicate compounds, however, many aspects need to be..... More

Abstract
The effect of Al addition on the microstructure and mechanical properties of extruded Mg-Sn based alloy is investigated by adding 1 wt% Al to the Mg-7Sn-1Zn alloy and indirectly extruding the billets with and without the Al addition. The Al addition promotes dynamic recrystallization (DRX) behaviour during hot extrusion, which..... More